DIY Rolling Storage Cart
By Brittney Smart
Brittney Smart
Brittney is a wife, a mom of four young children, a writer and editor (B.S. degree in English/Technical Writing), and a lover of interior design. She thrives on finding inexpensive ways to DIY her own home into a stylish yet family-friendly space.
Learn more about Homedit’s Editorial Process
| Updated on
Buy Now
Chic, stylish storage is the new black. These industrial-styled DIY rolling storage carts are a perfect solution for storage needs, whether hidden or on display for the world to see (or a hazy somewhere in between). In my home, storage space is at a premium; in fact, it’s pretty much nonexistent, until I spied the space under my daughters’ bed as a perfect space for some custom storage bins.
.jpg)
Start with your piece of plywood, cut to size. Cut two 1×4 pieces the length of your plywood (in this case, 21”). Set them next to the plywood but don’t do anything else with the wood yet.
Step 2 – Check the Measurements and Cut the Next Pieces
Measure from the outside edge of one 1×4 to the outside edge of the other 1×4, or simply add 1-1/2” to the width of your plywood. (In this case, the width was 16”, so the new measurement would be 17-1/2”.) Cut two 1×4 pieces to this size. Tip: Depending on the preciseness, or lack, of your cart floor, you may want to measure each side anyway and custom cut each board accordingly. I found that my measurements varied by up to 1/4”, so custom measuring and cutting made a better end product.
Step 3 – Add Wood Glue to the Length Boards
Run a line of wood glue along one side each of your length boards.
Step 4 – Attach the 1x4s to the Plywood
Attach the gluey 1x4s to the sides of the plywood.
Step 5 – Add the Front and Back Pieces
With the two longer sides glued in place, you’re ready to attach the front and back 1×4 pieces.
Place wood glue in a U-shape on the side of one of your 1×4 pieces.
Attach to the ends of your plywood and 1×4 side pieces. Repeat for other 1×4 end.
Step 6 – Add the Final Touches and Let Your Cart Dry
At this point, you should have four “walls” on your rolling cart. Run a thin line of wood glue along the interior seams and smooth it out with your finger (similar to caulking). Let dry completely.
ROLLING CART DESIGN #2: SQUARED CORNER BRACES
For those of you looking for additional support in the structure of your rolling cart, you might want to try adding in squared corner braces. To do this, complete the steps shown in the example above for Rolling Cart Design #1 up until the “let dry” step, then proceed as described below.
Step 1 – Create Four Pieces of Cut 2x4s
Take a 2×4 scrap, about 3” tall, and cut it in half, being sure to use the proper safety precautions in making such a cut. Repeat for one more 2×4 scrap, so you are left with four pieces of cut 2x4s.
Step 2 – Place Glue on Two of the Blocks
Place glue on the bottom and two sides of one of your 2×4 blocks.
Step 3 – Add Blocks to the Corner of Your Rolling Cart
Glue the 2×4 block into one corner of your rolling cart.
Repeat for the other three corners.
Step 4 – Leave to Dry
Wipe away excess glue. Let dry thoroughly.
ROLLING CART DESIGN #3: TRIANGLE CORNER BRACES
For the added support provided by corner braces but with less infringement on the actual storage space within your rolling cart, triangle corner braces are an excellent alternative. It takes slightly more steps than the squared corner braces, but not a lot. The end result is a strong, stable, and smooth rolling cart. Out of all three options, I’d recommend this one. To accomplish this, complete the steps for Rolling Cart Design #1, up until the “let dry” step, then proceed as described below.
Step 1 – Create a Triangular Piece with a Miter Saw
Adjust your miter saw to 45-degrees, then stand a 2×4 up on its short side (the 2” side).
Make the cut so that you’re left with a triangle piece of 2×4.
Step 2 – Cut the Triangular Piece in Half
Using appropriate safety precautions, cut this triangular 2×4 scrap in half short-wise, so you are left with two shorter pieces of triangular wood.
Step 3 – Repeat Again to Create Four Pieces
Repeat the triangular cuts so that you end up with a total of four short triangles. These will be your corner braces.
Step 4 – Glue the Triangles Into Your Cart
Place wood glue on the triangular bottom and two right-angle sides of a triangle piece.
Firmly press gluey triangle piece into a corner of your rolling cart.
Step 5 – Final Touches and Leave to Dry
Repeat for the other three corners, so that you have four triangle-braced corners when done. Let dry completely.
ALL ROLLING CART DESIGNS
Step 1 – Screw Support
When the glue on your rolling cart has dried thoroughly, you’re ready to move onto the next phase: screw support.
Tip: Because you’re working with the ends of wood pieces, always predrill your screw holes to prevent splitting.
For the Glued Corner Design #1: Screw the longer side pieces (21” sides, in this example) to the plywood. This will strengthen the glue seams. Tip: Pay attention to the placement of these screws, making sure they don’t “pop” out on the top of the plywood inside your rolling cart.
For the Squared and Triangle Brace Designs #2 and #3: Place two screws into each bracket on these side (21”) boards, for a total of four screws on each side board.
Your sides will look like this. If you want, you can add in a screw or two along the bottom into the plywood, but it’s not necessary if your fit is snug.
Step 2 – Prepare the Front of Your Rolling Cart
For all rolling cart designs: Decide which of the shorter boards will be the front of your rolling cart, then leave this front side completely alone for now. Turn your cart over so the back is facing upward, ready for drilling.
Predrill, then screw the ends of this back board (17-1/2” board, in this example) into the edges of the longer side boards (Glued Corner Design #1) or the braces (Squared and Triangle Designs #2 and #3), as well as the plywood.
At this point, the front of your rolling cart should be screw-free, while the other three sides of your cart should be secured with glue and screws. The Glued Corners Design #1 is done and ready to move on to staining.
For the Squared Brace Design #2: Predrill, being careful NOT to drill through the front board, then screw two 2” screws through the brace toward the front board. Repeat for the other front brace.
For the Triangle Brace Design #3: Carefully angle your drill into the triangle corner brace, being careful NOT to drill through the front board.
One or two screws in each triangle brace should hold the front board securely.
At this point, your braces should be holding both sides and the front and back securely, with the front board face showing no evidence of screw support.
Isn’t that clever of you?
ALL ROLLING CART DESIGNS
Step 3 – Sand Any Surfaces of Your Rolling Cart
Gently sand any surface of your rolling cart that needs it – specifically, the corners, sides, and the cart floor.
Step 4 – Prepare for the Painting or Staining Process
Elevate your rolling cart in preparation for staining/painting/whitewashing. Choose the finish that works for your style and taste! This example shows staining the rolling carts.
This example uses Minwax wood stain in dark walnut.
Brush the stain on with a brush.
Wipe off any excess stain every 3-5 minutes. (Sooner if you want a lighter look overall, or longer if you prefer a darker stain effect.)
Let the stain dry thoroughly.
Step 5 – Make the Leather Handles
While the stain on your rolling cart is drying, it’s a perfect time to move on to preparing your leather handles. After playing around with the leather a bit to see how curved/flat/long/short you want it, cut a piece of leather to your desired length (three pieces of leather are shown in this photo because I made three rolling carts for this tutorial).
Find the size of hole punch that will work best with your particular leather screws, bolts, or attachment pieces.
Punch a hole in the leather. If you don’t have a leather punch, you could try using a drill bit or a screwdriver and hammer. The holes themselves won’t be seen.
Make sure your leather screws/bolts fit snugly into the hole you’ve punched.
Admire your chic and sleek leather handles, but continue to wait for the wood stain to dry completely. It’s hard to wait but important for a beautiful finished product!
Step 6 – Attach the Leather Handles
When the stain has dried completely, measure and mark where you want your handles to be attached. Drill the two screws/bolt holes in the front board of your rolling cart.
Attach the leather handles.
Admire your handywork so far. You’re almost done! Just need to attach the casters.
Step 7 – Add the Four Casters
Attach your four casters on the four corners of your rolling cart.
Make sure, if you choose to screw into the plywood floor, that your screw is short enough to not pop through the other side.
I felt the casters were secure enough with just three (predrilled) screws placed into the two adjoining side boards, so I didn’t even bother with the fourth screw to secure it to the plywood.
Viola! You’re done!
This really is a showstopper, with the wood stain showing off the wood grain, the leather handles adding a modern, sleek look, and the casters providing exceptional functionality.
You’re ready to go find something to store under the bed (or sofa or desk) now, aren’t you? Good news: You can!
And you don’t have to be ashamed if a corner or two peek out from wherever you’ve rolled this storage piece to because it’s beautiful.
This is such a fun and easy project to complete and is ideal for a weekend DIY project. There are so many places in your home where you’ll find this to be a handy storage solution, and due to its low height, you can easily store it under your bed or desk.
The best thing about working with wood is that you can fully customize this project to your needs. Whether you want a subtly stained storage cart or a bold and colorful rolling storage cart, you can paint the cart once it’s finished to suit your home décor. I’m sure once you’ve made one rolling storage cart, you’ll be returning again to add a few more to your home.
We hope you enjoy making these DIY rolling storage carts, but more than that, we hope that they provide exceptional functionality and storage for your home and life. Happy DIYing!
Rolling Storage Cart (32″ H)
Shop Now
This is a horizontal carousel with slides that rotate manually. Use Next and Previous buttons to navigate.
Pressing the space bar will open it in full screen.
This is a carousel of product images. Use Next and Previous buttons to navigate, or jump to a slide with
the slide dots.
Rolling Storage Cart (32″ H) – Steel
$145.
00
Color :
Choose a Color variant
White
Black
quantity:
Sliding Storage.
Keep this three-tiered slim storage cart stocked with oils, spices, and seasonings. Super easy to roll in and out of place when cooking. This cart was designed tall and narrow to fit snugly against walls or between tight spaces. Great for stocking up supplies in other rooms, like the bathroom, as well.
Are the cart’s wheels removable?
Yes, they are, but when storing the cart without wheels, we recommend taking care that the bottom of the cart does not damage the floor.
Can the 3 tier rolling cart’s wheels be adjusted if unstable?
By adjusting the position of the top nut on the bolts of the wheels, you can level the rolling cart to address any stability issues the storage cart may be experiencing from an un-level floor.
Are the cart’s wheels removable?
Yes, they are, but when storing the cart without wheels, we recommend taking care that the bottom of the cart does not damage the floor.
Can the 3 tier rolling cart’s wheels be adjusted if unstable?
By adjusting the position of the top nut on the bolts of the wheels, you can level the rolling cart to address any stability issues the storage cart may be experiencing from an un-level floor.
As seen in real life
Show us your style using #theyamazakihome and tag us @yamazakihome
Customer Reviews
Sign Up for Newsletter
Be the first to know
Sign up to receive updates on product launches, inspiration, and special offers.
Carts and containers | Catalog of sports equipment ZSO “Dynamics”
ZSO-003560
Sports equipment storage rack (collapsible) Red
19 550 ₽
16 618 ₽ *
ZSO-003562
Rack on wheels for balls-hoops-jumping ropes (collapsible)
15 290 ₽
12 997 ₽ *
ZSO-003504
Rack-rack mobile one-sided for 25 balls (collapsible)
21 270 ₽
18 080 ₽ *
ZSO-003505
Ball trolley on wheels (collapsible)
10 600 ₽
9 010 ₽ *
ZSO-003506
Mobile ball storage container 1000x700x700 mm (collapsible)
11 900 ₽
10 115 ₽ *
ZSO-003508
Ball container with lid (collapsible)
13 900 ₽
11 815 ₽ *
ZSO-003510
Mesh container for balls with lid (collapsible)
15 900 ₽
13 515 ₽ *
ZSO-003121
Stand-rack mobile one-sided for 25 balls
20 350 ₽
17 298 ₽ *
ZSO-003726
Basket for sports equipment and balls on wheels for 60-70 balls
12 000 ₽
10 200 ₽ *
ZSO-003736
Basket for sports equipment and balls on wheels for 25-30 balls
11 500 ₽
9 775 ₽ *
ZSO-003801
Trolley for track and field poles and planks
13 500 ₽
11 475 ₽ *
ZSO-003802
Barrier trolley mobile
18 300 ₽
15 555 ₽ *
ZSO-002360
Ball trolley on wheels
9 590 ₽
8 152 ₽ *
ZSO-002694
Trolley for transporting mats 2000x1000x1000
7 900 ₽
6 715 ₽ *
ZSO-002998
Trolley for transporting mats 1870x970x110
4 900 ₽
4 165 ₽ *
ZSO-002396
Trolley for transporting mats 1500x800x200
4 200 ₽
3 570 ₽ *
ZSO-003763
Mesh sports equipment storage rack (collapsible)
33 000 ₽
28 050 ₽ *
ZSO-002442
Gate trolley (set of 2)
8 400 ₽
7 140 ₽ *
ZSO-002686
Ball trolley MIKASA AC-BC200W
22 416 ₽
19 054 ₽ *
ZSO-002630
Ball trolley TORRES
14 882 ₽
12 650 ₽ *
As a manufacturer/supplier of sports equipment and supplies, we can supply you with our products, products and goods for various areas of sports.
You can buy from us: “Carts and containers for the storage of sports equipment in sports halls”. We also suggest paying attention to the section “For sports halls”
We are a Russian manufacturer of products for sports, we have a large selection of sports goods in our assortment. Our production of sports equipment is located in the Moscow region . You can buy sports equipment with delivery from us, because we ship orders throughout Russia . Our managers will help you choose and purchase sports goods wholesale and retail, as well as advise on our discount policy.
Racks and racks for storage, trolleys, bags – Company “Partner”
Storage racks and racks, carts, bags – PARTNER Company – Essential equipment for the gym
Our company offers a large selection of storage racks and racks, carts, bags at competitive prices with delivery across Russia
Each sport requires special equipment and equipment to practice.
Therefore, convenient equipment, convenient and safe to use, was created specifically for their storage.
We offer a wide range of sports storage products:
- Containers
- Shelving units
- Stands
- Trolleys
- Trunk bags
- Children’s corners
and more.
All equipment and inventory necessary for the gym can be purchased from the Partner Company.
If you have any questions, you can ask us by phone, indicated in the contacts of our website or in the feedback form.
_____________________________________
The equipment of the school gym largely determines both the effectiveness of physical education lessons and the attitude of students to this subject.
Types of racks for installation:
- Wall-mounted – installation along the wall, a traditional solution, indispensable in small or narrow spaces.
- Double-sided – placed away from the wall. Can be used for room zoning.
Types of racks by design:
- Open – classic racks made of shelves with side walls in the form of a profile.
- Closed – by design they are cabinets with mesh facades. The doors are locked with a key, which makes the inventory inaccessible to outsiders.
- Special racks – designed to store certain types of equipment, such as balls, skis, skates. There are drying racks for shoes, some models are equipped with a heating element, which allows you to quickly put things in order.
Sports equipment racks are made of metal and plastic. Plastic products – racks, baskets – have an advantage when used in environments with high humidity, such as swimming pools. In addition, their price is much lower.
When choosing gym equipment , the following requirements must be taken into account:
- Safety. This applies both directly to structures, the operation of which should not lead to injuries, and their coatings.
- Versatility. Equal opportunities for the use of sports equipment should be provided for all categories of students.
- Mobility. Often in physical education lessons, students themselves carry shells, assemble structures, so all of them should be easily transportable, without difficulties in assembling and disassembling.
- Wear resistance. Equipment elements will be actively used by hundreds of children, which means that all of them must withstand high operational loads. It is also desirable that the inventory be made in an anti-vandal version.
- Modern design. The aesthetic aspect should also not be forgotten, because the visual appeal of the equipment increases interest in physical education.
This applies both directly to structures, the operation of which should not lead to injuries, and their coatings. Advantages of the equipment for the gym presented in the catalog of the Partner Company:
- full compliance with the requirements and norms of the Federal State Educational Standard;
- all sporting goods are made of environmentally friendly materials;
- minimum injury risk of all complexes and their individual elements.
