Jack for headset: Differences Between 2.5mm, 3.5mm & 6.35mm Headphone Jacks – My New Microphone

Differences Between 2.5mm, 3.5mm & 6.35mm Headphone Jacks – My New Microphone

Although the popularity of wireless headphones continues to increase, wired headphones and their associated headphone jacks are still used regularly. There are a few different headphone jack sizes we should be aware of when using our wired headphones. These sizes are 2.5mm (3/32″), 3.5mm (1/8″) and 6.35mm (1/4″).

What are the differences between 2.5mm, 3.5mm & 6.35mm headphone jacks? The primary, most obvious difference is size. The numbers given refer to the diameter of the jack but the lengths of the connectors are also different. Certain applications have certain standard sizes. In terms of wiring, various standards can be applied to each size jack.

So in this article, we’ll talk about the nuanced differences between headphone jacks along with the similarities these jacks share.


A Primer On Jacks And Plugs

Before we get started, let’s first understand the difference between a headphone jack and a headphone plug.

The headphone jack is the receptacle, and the headphone plug is inserted into the jack. In other words, the headphone jack is the female connector, and the headphone plug is the male connector.

If your headphones are permanently wired, the end of the cable features a plug. Your audio player, smartphone, laptop, etc., has a headphone jack that you plug your headphones into.

Headphone Plug
3.5mm FosPower (link to check the price on Amazon)Headphone jack of an iPhone 6S (above) and a headphone plug (below)

Note that when people say “headphone jack,” they are sometimes referring to the plug. This primer is not only to distinguish between the two but also to ensure clarity in the remainder of this article when we discuss jacks and plugs together.

Related article: What Is The Difference Between A Microphone Plug And Jack?


The Size Difference

The most obvious difference between 2.5mm, 3.5mm and 6.35mm headphone jacks is in the name itself: the size of the jack and its associated plug.

The quoted size refers to the diameter of the jack/plug, and each size has its own length(s) as well. Here are the specified dimensions for each headphone jack size:

Plug Diameter Plug Length
2.5mm 11mm
0.43″
3.5mm (~1/8″) 14mm – 17mm
0.55″ – 0.69″
6.35mm (1/4″) 30mm – 31mm
1.18″ – 1.22″

As we can see from the table above, there isn’t always a set standard for the lengths of the specific plug sizes. Though 2.5mm connectors are nearly all regulated to be 11mm in length, 3.5mm and 6.35mm plugs have some variation.

3.5mm plugs are usually 14mm long but can, in some instances, be as long as 17mm and still be considered standard. 15mm and 17mm are used in video applications, though 17mm is quite rare. 3.5mm headphone jacks are typically designed to receive either 15mm or 17mm plugs.

6.35mm or 1/4″ plugs are a bit more standardized and have a smaller range in length between 30mm – 31mm (1. 18″ – 1.22″). This small difference is not overly critical when it comes to proper connectivity between quarter-inch plugs and jacks.

The vast majority of wired headphones have 3.5mm-diameter 15mm length TRS or TRRS connectors. These work perfectly will most consumer audio devices (portable music players, smartphones, laptops, tablets, etc.). Professional headphone amps typically have 1/4″ TRS jacks, and so many pro headphones come with a 3.5mm-to-6.35mm adapter.

Let’s get into the different sizes in more detail here:

The 6.35mm (1/4″) Plug & Jack

If you’ve ever played an electric guitar or bass through an amplifier, you’ve used a 6.35 (1/4″) TS “patch” cable. This patch connection has the same dimensions as the 1/4″ headphone plug/jack. However, the headphone jack typically uses an extra pole/conductor in its connector, making it a TRS (tip-ring-sleeve) rather than a TS (tip-sleeve).

The 6.35mm is relatively bulky and is generally reserved for professional headphones and other professional audio devices. These devices include but are not limited to headphone amplifiers, audio interfaces, digital-to-analog converters, mixing consoles and field recorders.

Here is a picture of a 6.35mm (1/4″) TRS headphone plug:

6.35mm (1/4″) Headphone Plug

Here is an example of a simple one-channel headphone amp with a 1/4″ (6.35mm) headphone jack to the right of its front face:

Schiit Magni 3 Heresy Headphone Amp With 6.35mm (1/4″) Headphone Jack
Link to check the price on Amazon

Schiit is featured in the following My New Microphone articles:
• Top 11 Best Headphone Amplifier Brands In The World
• Top 11 Best Power Amplifier Brands In The World
• Top 11 Best Desktop DAC (Digital-Analog Converter) Brands

The 3.5mm (1/8″) Plug & Jack

Most analog wired headphones today have 3.5mm (1/8″) plugs. The 3.5mm connector is also used in auxiliary “aux” audio connections commonly found in automobile audio consoles, mixing consoles, and other consumer products.

Note that, due to smartphone manufacturers abandoning the headphone jack, lighting and USB-C digital headphone connectors are becoming common, as are wireless Bluetooth headphones.

3.5mm headphone jacks are found in portable audio players, laptops, smartphones, tablets, field recorders, mixing consoles, and many other audio devices. Headphones typically use TRS 3-pole 3.5mm connectors, while headphones with a microphone will utilize TRRS 4-pole 3.5mm connectors.

Here is a picture of a 3.5mm TRS and a 3.5mm TRRS headphone plug:

3.5mm (1/8″) TRS Plug (left) – 3.5mm (1/8″) TRRS Plug (right)
Links to check the Cable Creation 3.5mm TRS and TRRS cables on Amazon

And here’s a picture of my MacBook Air’s 3.5mm headphone jack (the computer I’m using to write this article!):

MacBook Air 13-inch Early 2015 3.5mm Headphone Jack

Related articles:
• Are AUX (Auxiliary) Connectors & Headphone Jacks The Same?
• How To Clean A Headphone Or Aux Jack Properly And Safely

The 2.

5mm Plug & Jack

The 2.5mm (3/32″) connector is less common in pro audio applications. However, it still gets used regularly in two-way radios (walky-talkies) and some video cameras.

Here is a picture of a 2.5mm TRS headphone plug:

2.5mm (3/32″) TRS Plug

And here is a picture of a two-way radio that has a 2.5mm headphone jack:

Tait TP93/94 Speaker Microphone with 2.5mm Headphone Jack


Headphone Jacks Are Not Only For Headphones

These connectors are often referred to as headphone jacks, and, in many instances, they are used for headphones hence the name. If a jack is specifically meant for headphones, it’s often referred to as a headphone jack. However, the 2.5mm, 3.5mm and 6.35mm connectors mentioned above are used for much more than just headphones.

Because there are plenty of other uses for these jacks that do not include headphones, it’s sometimes better to refer to them generically as “audio jacks”.

For example, these audio jacks can be used in the following applications:

  • Microphones
  • Headsets (headphones + microphone)
  • Audio in/auxiliary
  • Audio out/auxiliary
  • Electric musical instruments (electric guitar, electric bass guitar, keyboards, etc. )
  • Loudspeakers
  • Studio monitors
  • Studio patch bays

It’s important to remember that not all plugs and jacks are used exclusively for headphones.


Wiring Standards

Things get a bit tricky when it comes to wiring standards of headphone jacks. In this section, we’ll discuss the 2.5mm, 3.5mm, and 6.35mm headphone plugs/jacks in terms of how they connect and the various signals they can send.

Tip, Ring & Sleeve

To understand the wiring of audio jacks and plugs, we must understand the different pole-counts at the plug and jack and the internal wires that carry audio from the cable.

The poles/conductors are best-known as tips, rings, and sleeves. These labels refer to the location the conductors are designed in a jack/plug.

The tip is at the tip of the plug; the rings are electrically isolated and wrap around the plug’s circumference in the middle of its length, and the sleeve is toward the base of the connector.

In each of the headphone connections, we notice that the electrically conductive plug has a larger diameter housing below it. This housing isn’t only to mark the end of the connector and prevent damage but also to house the electrical connection between the signal wires in the headphone cable and the individual poles in the plug connector.

If we took apart an audio plug, it would look similar to this:

The coinciding conductors on the interior of the connectors attach to the signal wires in the audio/headphone cable to effectively move the audio signal from one place to another. In the case of headphones, this path is from the audio device to the headphones.

The sleeve of the connector is typically connected to electrical ground while also providing a tubular shield within the cable rather than a single wire. The shield provides some rejection of electromagnetic interference in the signal wires while having it grounded provides a zero-potential for the other signal wires to be referenced against.

To learn more about headphone cables, check out my article An In-Depth Look Into How Headphone Cables Carry Audio.

TS (Tip-Sleeve)

In the case of a TS connector, the sleeve acts as the ground and also as a return for the audio signal. When used for headphones, the wiring is as follows:

  • Tip: Mono headphone signal
  • Sleeve: Ground & mono headphone signal return

More generally, the TS connector is wired with:

  • Tip: Signal
  • Sleeve: Ground & return

The TS is not often used for headphones since it cannot carry a stereo audio signal.

TRS (Tip-Ring-Sleeve)

The TRS connector is much more common because it allows for stereo audio. That being said, a much more rare circumstance (for headphones, at least) is the TRS carrying a balanced mono signal.

Unbalanced Stereo TRS:

Unbalanced stereo wiring is the most common in wired headphones. It allows the left and right channels of the stereo audio signal to be carried to their coinciding sides of headphones (or their corresponding earbuds).

Unbalanced stereo TRS is generally wired as:

  • Tip: Left headphone signal
  • Ring: Right headphone signal
  • Sleeve: Ground/returns

The term “unbalanced” means that the proper audio signal is sent along one wire only. This method is fine, though the signal may be susceptible to electromagnetic and radio frequency interference, and a longer cable length may degrade the signal.

In the case of unbalanced stereo audio, two separate unbalanced signals are being carried through the cable. The left channel audio signal is carried on the tip (with the sleeve acting as the return), while the right channel audio signal is carried on the ring (with the sleeve acting as the return).

The tip connects to a wire that goes to the positive (+) lead of the left headphone driver coil; the ring connects to a wire that goes to the positive lead of the right driver. The sleeve connects to a wire that goes to both negative (-) terminals of the driver coil. This wire usually has a solder joint in the “Y” or in the earpiece where the ground wire from the plug splits into separate wires that connect to the negative terminals of the driver coils.

Balanced Mono TRS:

Balanced TRS cables are rarely ever used for headphones since they are not stereo.

Rather, they are often used for connecting individual left channel and right channel outputs to studio monitors and as patch bay cables to route balanced signals around a music or broadcast studio.

For your information, balanced TRS is wired like this:

  • Tip: Positive polarity headphone signal
  • Ring: Negative polarity headphone signal
  • Sleeve: Ground

Connecting a pair of headphones to a balanced output (like the left channel output of an audio interface, for example) would send equal signals with opposite polarities to the headphone’s drivers, and the resulting sound would be quite awful.

As an aside, balanced TRS is wired in the same fashion as 3-pin XLR with tip bring pin 1, ring bring pin 2, and sleeve being pin 3.

TRRS (Tip-Ring-Ring-Sleeve)

TRRS headphone plugs are what we’ll often find with consumer-grade headsets and earbuds that have built-in microphones. With 4 poles, this connector can effectively carry a stereo headphone signal and a mono microphone signal with a common ground.

There are two standards we see with TRRS cables: CTIA and OMTP:

CTIA Standard For TRRS
  • Tip: Left headphone
  • Ring: Right headphone
  • Ring: Ground
  • Sleeve: Microphone

CTIA is the new standard and has been adopted by practically all producers of consumer-grade audio devices since 2015. Smartphone, laptop and tablet manufacturers have switched over from the old OMTP standard, so the headsets and headphones with built-in microphones on the market today are also wired with the CTIA for compatibility.

OMTP Standard For TRRS

For your information, here is the older OMTP standard that may be the wiring scheme in an older audio device or pair of headphones you own.

  • Tip: Left headphone
  • Ring: Right headphone
  • Ring: Microphone
  • Sleeve: Ground

It’s important to note that not all headsets use the TRRS connection. In fact, many professional broadcasting headsets use completely different connectors for the headphones and the microphone for improved versatility.

Computer and video game headsets will often use various USB types to connect. Older, fixed-line desk phones often use RJ9 (RJ10 or RJ22). Headphones and headsets designed for newer iPods connect via Lightning connectors.

TRRRS (Tip-Ring-Ring-Ring-Sleeve)

TRRRS gives us 5 poles to work with but is rare in 2.5mm, 3.5mm and 6.35mm connectors. Rather the TRRRS design is combined with the relatively unfamiliar 4. 4mm connector, which we’ll get to shortly.

The TRRRS has great potential for various wiring schemes. A proper wiring design for the TRRRS headphone plug/jack is:

  • Tip: left channel (positive polarity)
  • Ring: left channel (negative polarity)
  • Ring: right channel (positive polarity)
  • Ring: right channel (negative polarity)
  • Sleeve: ground/shield

Again, we’ll discuss this in more detail when we touch on the 4.4mm audio jack.

For a detailed article on headphone connection/wiring standards, check out my article An In-Depth Look Into How Headphone Cables Carry Audio.


Other Headphone Connectors

As briefly mentioned above, not all headphones utilize the 2.5mm, 3.5mm or 6.35mm connectors. There are plenty of other options out there. Here are a few:

Lightning

When Apple did away with the headphone jack on their iPhones, a whole new range of headphones came out that utilized the Lightning connector (the charging port of iPhone since the iPhone 5).

Pictured below are Apple’s Earpods with Lightning connector (link to check the price on Amazon):

Apple Earpods with Lightning Connector

Apple is featured in My New Microphone’s Top 14 Best Earphone/Earbud Brands In The World.

The lightning port can be used for headphones, headsets, and microphones, too. Check out My New Microphone’s Top 4 Best External (Lightning) Microphones For iPhone Audio for more info.

USB

Following Apple’s lead, many other smartphone manufacturers have ditched the headphone jack. This has opened up a new market for USB-C headphones.

Here is a picture of the consumer-grade Lewder In-Ear Headphones (link to check the price on Amazon):

Headphones with USB-C connector

There are also many headsets out there that utilize USB-A as their connector. The Logitech h490 headset (link to check the price on Amazon) is one such example:

Logitech h490

XLR

Some professional headphones and headsets utilize XLR to make their connection. Many of these headphones/headsets have detachable cables that offer a variety of connections to choose from, including XLR.


The 4.4mm Audio Jack

4.4mm TRRRS Audio Jack

As discussed previously, there is also a lesser-known 4.4mm headphone jack.

The 4.4mm Pentaconn is a relatively new balanced plug that sits somewhere between a 3.5mm headphone jack and a high-end XLR. It is typically a 5-pole TRRRS and is currently used in professional audio and the telecommunication industries.

The TRRRS has great potential for various wiring schemes. This is the most common in terms of headphones:

  • Tip: left channel (positive polarity)
  • Ring: left channel (negative polarity)
  • Ring: right channel (positive polarity)
  • Ring: right channel (negative polarity)
  • Sleeve: ground/shield

So with the 4.4mm TRRRS connector, we get two balanced channels for a balanced stereo signal. Balanced audio is less susceptible to electromagnetic and radio frequency interference, signal degradation and headphone cross-talk making it a quiet, more effective way of carrying stereo audio to your headphones.

Of course, many would argue that balanced headphone connections like the 4.4mm TRRRS are not worth the extra cost and provide minimal enhancement over unbalanced stereo. However, the science of balanced vs. unbalanced audio is clear. The question then becomes, is the extra cost worth it to you?


Adapters

Fortunately, there are adapters for pretty much any change in connector you could want.

The most common adapter is the 3.5mm female to 6.35mm male.

This adapter from UGREEN (link to check the price on Amazon) is a perfect example of a 3.5mm F to 6.35mm M headphone adapter.

UGREEN 3.5mm F to 6.35mm M Headphone Adapter

Many headphones on the market will have a 3.5mm connector and come with a 3.5mm F to 6.35mm M adapter.


Wireless & Bluetooth Headphones

Let’s bring our discussion back to Apple’s decision to get rid of the headphone jack in their smartphones. This seemingly big move was not done lightly. There had to be an alternative other than the Lightning cable to prompt such a big choice. That alternative was wireless headphones and, more specifically, Bluetooth headphone technology.

Wireless headphones work with a transmitter and receiver. The transmitter emits the source audio wirelessly, and the receiver, which is built into the headphones, picks up the audio to convert it into sound.

These wireless audio signals are encoded, which means they are carried within another signal rather than being transmitted as audio waves. The wireless signals are often in the radio-frequency or infrared frequency range. Note that encoding must take place, or else the audio signal would be propagated as audible sound.

So a more accurate description would be that the transmitter takes the audio signal, encodes it, and sends it to the receiver wirelessly. The receiver then decodes the wireless signal to access the audio signal, amplifies the audio signal, and converts the audio into sound.

With that said, let’s quickly run through the wireless headphone connections.

Radio Frequency Wireless Headphone Connection

RF wireless headphones, as the name suggests, utilize radio frequencies to transmit audio signals wirelessly. The range of frequencies is typically either in the very high frequency/VHF (30 MHz – 300 MHz) or in the ultra-high frequency/UHF (300 MHz – 3 GHz) range.

Wireless headphone manufacturers will generally design their products to work in a specific and small range of radio frequencies.

RF signals typically travel 15m to 100m and do not require line-of-sight between the transmitter and receiver to function properly.

With RF wireless headphones, we can have as many headphones listening to the same RF channel as you’d like.

Unfortunately, RF is susceptible to interference and static when listening. Low-level noise and a relative lack of bass are also often present in RF wireless headphone signals.

Bluetooth Wireless Headphone Connection

Bluetooth is an international digital wireless standard. It encodes and transmits digital audio rather than analog audio (like most RF and IR wireless systems). Bluetooth actually works with RF frequencies in a band of 79 different frequencies centred on 2.45 GHz.

Bluetooth can connect to 8 different devices simultaneously with no interference. Each connection changes frequencies 1600 times per second to ensure this.

Related article: How Bluetooth Headphones Work & How To Pair Them To Devices

Infrared Wireless Headphone Connection

Infrared wireless headphones transmit audio encoded in infrared waves (frequency range from 300 GHz – 430 THz).

IR wireless provides a cleaner signal than RF at the expense of being reliant on line-of-sight.

This is similar to how a TV remote control interacts with a television.


What is the difference between a headphone jack and an audio out? A headphone jack outputs audio (typically unbalanced stereo) that is meant for headphones. Audio outs commonly output balanced or unbalanced mono signals, which would not drive headphones properly and may not have the proper output voltage or impedance for optimal compatibility with headphones.

Can speakers be plugged into a headphone jack? Although you can, it is not advised unless the speakers are stereo and designed to accept the voltage and impedance levels of the headphone out. Plugging a speaker designed to accept speaker level audio may not yield the best results when plugged into a headphone output. In some cases, it may even damage the jack and the output circuit.


Choosing the right headphones or earphones for your applications and budget can be a challenging task. For this reason, I’ve created My New Microphone’s Comprehensive Headphones/Earphones Buyer’s Guide. Check it out for help in determining your next headphones/earphones purchase.


Definition of headphone jack | PCMag

The analog socket used to plug in a headset, earphones or headphones. The 2.5 and 3.5mm jacks have been used on cellphones and smartphones, while stereo and home theater equipment generally have a 6.3mm socket.

Increasingly Eliminated

Common on mobile phones for decades, the 3. 5mm headphone jack is vanishing. For example, there is none starting with the iPhone 7 in 2016 and Samsung’s Galaxy S20 in 2020. An adapter for a wired headset or a Bluetooth wireless headset must be used instead. See mini-phone connector, phone connector, headphones, earphones and Lightning connector.

Headphone Jacks
The 2.5 and 3.5mm jacks have been used with mobile devices, while the 6.3mm connectors (bottom) are found on non-portable audio equipment.

Advertisement

PCMag Stories You’ll Like

{X-html Replaced}

Editors’ Choice

THIS DEFINITION IS FOR PERSONAL USE ONLY. All other reproduction requires permission.
Copyright © 1981- 2023. The Computer Language(Opens in a new window) Co Inc. All rights reserved. PCMag Newsletters

PCMag Newsletters

Our Best Stories in Your Inbox

Follow PCMag

  • Facebook (Opens in a new window)

  • Twitter (Opens in a new window)

  • Flipboard (Opens in a new window)

  • Google (Opens in a new window)

  • Instagram (Opens in a new window)

  • Pinterest (Opens in a new window)

PCMag. com is a leading authority on technology, delivering lab-based, independent reviews of the latest products and services. Our expert industry analysis and practical solutions help you make better buying decisions and get more from technology.

How We TestEditorial Principles

  • (Opens in a new window)
    Ziffmedia Logo

  • (Opens in a new window)
    Askmen Logo

  • (Opens in a new window)
    Extremetech Logo

  • (Opens in a new window)
    ING Logo

  • (Opens in a new window)
    Lifehacker Logo

  • (Opens in a new window)
    Mashable Logo

  • (Opens in a new window)
    Offers Logo

  • (Opens in a new window)
    RetailMeNot Logo

  • (Opens in a new window)
    Speedtest Logo

(Opens in a new window)

PCMag supports Group Black and its mission to increase greater diversity in media voices and media ownerships.

© 1996-2023 Ziff Davis, LLC., a Ziff Davis company. All Rights Reserved.

PCMag, PCMag.com and PC Magazine are among the federally registered trademarks of Ziff Davis and may not be used by third parties without explicit permission. The display of third-party trademarks and trade names on this site does not necessarily indicate any affiliation or the endorsement of PCMag. If you click an affiliate link and buy a product or service, we may be paid a fee by that merchant.

  • About Ziff Davis(Opens in a new window)
  • Privacy Policy(Opens in a new window)
  • Terms of Use(Opens in a new window)
  • Advertise(Opens in a new window)
  • Accessibility(Opens in a new window)
  • Do Not Sell My Personal Information(Opens in a new window)
  • (Opens in a new window)
    truste logo

  • (Opens in a new window)

Types of headphone jacks

Wired headphones can now be connected to any multimedia device. Each gadget has a corresponding connector for connection. There is no single standard for connecting headphones, there are several similar ones.

We will look at the main types of headphone jacks , explain where they are used, and show their appearance.

Mini Jack

This headphone input is the most popular in the world. It appeared a long time ago, but even now this standard functions in full, there is no replacement for it. All smartphones, computers and other devices are equipped with a mini-Jack. Of course, except for the latest iPhones, where this connector was abandoned. Mini jack size 3.5 mm.

Jack

Quite an old standard, which is more used in professional audio equipment. Previously, DVD players had a similar input. Now Jack is used in musical instruments: such as: electric guitars, and more.

Micro Jack

Micro Jack – also called headphone jack . It practically does not differ from a mini-jack, except for the size (2.5 mm). Previously, it was used in mobile technology (for example, Nokia 6120 Classic), but the standard did not take root, and manufacturers decided to use a 3.5 mm jack in their devices.

USB connection

This type of headphone jack is quite rare. These headphones are used by e-sportsmen. They have many additional buttons and are very finely tuned.

Technical features

Jacks of the same size may also differ in the number of strands. For example, a familiar 3.5 mm jack can have both 3 and 4 wires. In the first case, mono sound is transmitted, in the second we have a full-fledged stereo sound.

In most cases, headphones come across with two-channel sound. If there is a microphone, then this is already a headset, which means that there will be one more additional contact on the connector.

Past versions

Some people currently have older phones that have outdated connectors. They do not have a specific name, since each manufacturer made connectors exclusively for its model range. For example, headphones from Sony phones did not fit Nokia or Samsung, and vice versa.

Today, 99% of all mobile devices are equipped with a Mini Jack connector and are fully compatible with each other.

Output

The most popular headphone jack is the Mini Jack. This connector can be considered almost universal, since today almost all devices have a 3.5 mm jack on board.

Did you like it? Share with your friends!


Date: 10/17/2017
Author/Translator: ThreePC

What is the name of the headphone jack: how to connect headphones correctly.

Headphones are one of the most important accessories connected to a computer. They give us the opportunity not only to listen to music or watch any video without distracting others, but also to communicate with friends and family using programs such as Skype or Viber. In addition, it is much more comfortable to play video games with headphones, because they allow you to achieve complete immersion in what is happening on the screen.

But how to properly connect headphones and understand their device? What is the name of the connector with which they are connected? You will learn about all this in this article.

Contents of the article

  • What are the names of the headphone jacks
  • How to connect headphones
  • Features of connecting USB headphones for connecting headphones is “officially” called TRS. This is an English abbreviation of the words tip, ring and sleeve, which translates as tip, ring and sleeve, respectively.

    But at present, and especially in everyday life, this name is used quite rarely. In most cases, you can hear such a name as “jack”. This is the English translation of the word “nest”. A simple and quickly remembered word was liked by many owners of headphones, so we will call it that way.

    Jack is exactly the connector on the device itself, where the accessory is connected, but the plug, which is sometimes also not translated into Russian, is called “plug” in English. But very often you can hear about several jacks at once, namely: just a jack and a mini-jack. What is the difference?

    A “simple” jack is a connector with a diameter of 6. 3 millimeters. It is used in a professional environment – when connecting technically powerful headphones, microphones, guitars or amplifiers for it. That is, this input will be familiar to any musician.

    Mini-jack – almost the same, but the diameter of the connector is only 3.5 mm. One way or another, any inhabitant had to deal with it – this is a connector for a headset, simple headphones for a computer, player and other similar devices.

    IMPORTANT! Sometimes phones also use a microjack – this connector is very small – 2.5 millimeters, but it is quite rare.

    How to connect headphones

    Connecting headphones to a computer is not difficult, but for those who have never done it before, there may be some difficulties. Especially if it is a device that also has a microphone, due to which it has two colored plugs at once.

    Remember – the red plug is always responsible for the correct operation of the microphone. It is unlikely that it will be possible to confuse and insert it into the green connector, but there are situations when you need to connect only headphones and then you should understand that you need to insert the green plug.

    In addition, sometimes there are no large headphones with you, so a headset will help out – in this case, the plug must also be inserted into the green connector. But in new laptop models, there are sometimes combined jacks where you can insert a headset equipped with a microphone. They have the same round shape, and there is a special icon next to it indicating that this is a socket for a combined device.

    After you have connected the accessory, adjust the volume and you can start using the headphones.

    Features for connecting USB headphones

    There are also devices that connect via the USB port. This is very convenient, since the vast majority of modern household appliances are equipped with such a socket – this is due to the spread of flash drives, with which you can store and transfer information. Flash drives are inserted through the same port, so it is available not only on the oldest computers and laptops, but also on many tablets, TVs and even phones.

    Computers and laptops often have several such connectors at once, which makes it easier to use the device – you can connect special headphones, a flash drive, and, for example, a computer mouse.

    USB headphones have their own features that you should definitely pay attention to when choosing:

    1. They have a built-in amplifier, which allows you to achieve more powerful and clear sound. That is why the use of such an accessory will be very useful in combination with a phone or tablet, which in most cases provide not too intense sound.
    2. Another built-in element is its own sound card. In addition to allowing you to listen to music or other audio tracks in better quality, such a card may be the only way to listen to something if the card on your phone or other device breaks.